How to Set up a Bathtub: Set Up an Acrylic Bathtub as Well as Tub Surround
How to Set up a Bathtub: Set Up an Acrylic Bathtub as Well as Tub Surround
Blog Article
On this page below you can locate additional helpful answers in regards to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately tough task. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall surface to eliminate the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub as well as set in the new one. See to it you have actually certified yourself for the job and are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new bathtub in your bathroom if you have actually already bought a brand-new bathtub and don't require to alter the arrangement of your previous water pipes.
Your tools and also material checklist need to make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic because of the limited accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Tub
Utilizing the two wood boards under its feet, position the bath tub in the called for setting. The wood boards are valuable in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bath tub till the level checks out level.
To install taps, fit the bottom of the furthest flexible tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water system as well as inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill up the bathtub as well as additionally check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bathroom paneling as defined in the producer's instruction manual. Tiling and also securing around the tub should wait till the tub has been used at the very least once as this will resolve it into its final setting.
Preparing for the Installment
First of all, the supporting structure supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to prevent strain on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last placement.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealant can crack rather very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about How to Install a Bathtub Yourself? Leave a remark down below. We'd be delighted to know your insights about this write up. We are looking forward that you come back again before long. If you please take the time to distribute this blog entry if you enjoyed it. Thanks so much for going through it.
Schedule Free Estimate
Report this page